Rohit Vinay Mukane
Swadeshi Mill, Sion-Chunabhatti, Mumbai
Email : rohitmukane56 AT gmail.com
EDUCATION :
** M.TECH (Instrumentation & Control) Vishwakarma Institute of Technology ( VIT, Pune ) 2015-2017
** B.E (Electronics & Telecommunication) Mumbai University (MGM-CET, Mumbai) 2010-2014
** H.S.C Maharashtra State Board 2009-2010
** S.S.C Maharashtra State Board 2007-2008
WORK EXPERIENCE :
Vedang Cellular Service Pvt.Ltd. Mumbai :
** Operation & Maintenance Engineer December 2018 – Present
** Responsible for corrective maintenance and preventive activities for the sites.
** Interact with NOC team to learn for clearing faults.
** Responsible for alarm clearance on service affecting and non-service affecting categories at site.
** Conduct Acceptance Test for new sites before the same goes ‘’Commercially Operational’’.
** Strict adherence to applicable OHS (Occupational Health & Safety) guidelines.
Welkin Telecom Infra Pvt.Ltd. Mumbai :
Project Engineer August 2017 – December 2018
** Installation, commissioning and testing of BTS/eNode-B/BSC/MSC equipment’s in 2G/3G and 4G Technologies
** Installation, Commissioning and alignment of Microwave.
** Carry out all the tests like VSWR and submit results to customer.
** Installation & Commissioning of all electrical equipment like rectifier etc. Up gradation/Swapping of BTSs/BSCs/ RF & MW Antennas.
** Team Coordination,NetworkMaintenance,Quality Assurance
Vedang Cellular Service Pvt.Ltd. Mumbai :
Project Engineer March 2015 – June 2016
** RF Surveys – To determine the location of new sites to be installed for cellular operators.
** Benchmarking Drive Test – To benchmark various operators based on a detailed drive test done in the entire city and by capturing Network parameters.
Forbes Marshall Pvt. Ltd, Pune (R&D Department) :
** Project Trainee Engineer June 2016 – July 2017
** Designing, developing, installing and testing the LabVIEW systems.
** Supervised and performed LabVIEW development.
** Programmed and documented the LabVIEW systems.
** Developed automated test, data acquisition, and control systems.
** Prepared LabVIEW programs for control applications.
** Programmed for real-time based monitoring and control systems.
** Assisted in designing and development of LabVIEW applications for specific system requirements.
** Performing research and development to enhance the utility of LabVIEW.
TECHNICAL SKILL SUMMARY :
Languages : NI LabVIEW Programming, Basic C Programming, Assembly Language.
Simulation Software’s : NI Max, MATLAB,Eagle, Proteus, MultiSim, Latex, Linux.
PROJECTS UNDERTAKEN :
Title : : LabVIEW Based Implementation of Fuzzy Logic for Vibration Analysis to Identify Machinery Faults Aug 2016 - July2017.
Description : Machine fault detection is very advantageous for diagnosis of faults before it occurs and to protect the machinery from catastrophic damages.
Vibration monitoring is important for running rotating equipment evenly for years. The proposed work shows a novel approach of classification using fuzzy logic for decision making about the machine condition using NI LabVIEW.
Technical Environment :
** NI LabVIEW 2015
** NI Data Acquisition Card
Title : Real-Time PID Implementation Using LabVIEW for Flow Control Loop Aug 2015-May2016.
Description : PID controllers are widely used in industrial control systems because of the reduced number of parameters to be tuned. The main objective is to identify the system model for a flow control loop and implement PID controller in NI LabVIEW for real-time experimentation.The flow control loop was interfaced to a computer via NI-USB DAQ-6215 card and PID was implemented using LabVIEW.
Technical Environment :
** LabVIEW 2014
** MATLAB 2015
Title : Advance Power Monitoring and Theft Prevention using SCADA July 2013 – May 2014.
Description :In this project we attempt to improve the current power distribution scenario by using SCADA technology. We will measure and monitor power at various load points in our model. Using that data, we will define the load shedding technique through controlled automation. This entire monitoring will happen using a personal computer. There will be real time feedback about the faults at generation points, distribution points.
Technical Environment :
** PCB Express
** Eagle, MultiSim.
ACADEMIC & EXTRACURRICULAR ACHIEVEMENTS & ACTIVITIES :
** Presented a paper on ‘LabVIEW Based Implementation of Fuzzy Logic for Vibration Analysis to Identify Machinery Faults’ at 3rd International Conference on Computing, Communication, Control and Automation 2017.
** Worked as Lab Assistant for CP labs for 1st year engineering at VIT, Pune.
** Cleared GATE-2014 Electronics & Communication Engineering.
** Worked as ‘Committee Member’ under the IETE committee of MGM-CET, 2012-13.
** Worked as ‘Event Co-ordinator’ of TECH ARETE 2012-13 & 2013-14.
** Awarded as 'Ideal Student' of K.V. High School, Jawhar, 2008-09.
PERSONAL DETAILS :
Name : Rohit Vinay Mukane
Date of Birth : 30-07-1992
Languages Known : English, Hindi and Marathi.
DATE :
PLACE :